fr10-005 thru fr10-10 page: 1 frontier electronics corp. 667 e. cochran street, simi valley, ca 93065 tel: (805) 522-9998 fax: (805) 522-9989 e-mail: frontiersales@frontierusa.com web: http://www.frontierusa.com 1a fast recovery plastic rectifier fr10-005 thru fr10-10 features z fast recovery times z ul 94v0 flame retardant epoxy molding compound z diffused junction z low cost z high surge current capability mechanical data z case: transfer molded, do41, dimensions in inches and (millimeters) z leads: solderable per mil-std-202, method 208 z polarity: cathode indicated by color band z weight: 0.34 grams maximum ratings and electrical characteristics ratings at 25 c ambient temperature unless otherwise specified single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% ratings symbol fr10-005 fr10-01 FR10-02 fr10-04 fr10-06 fr10-08 fr10-10 units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current 0.375?(9.5mm) lead length at ta=55 c i o 1.0 a peak forward surge current, 8.3ms single half sine-wave superimposed on rated load i fsm 30 a typical junction capacitance (note 1) c j 15 pf typical thermal resistance (note 2) r ja 50 /w storage temperature range t stg - 55 to + 150 operating temperature range t op - 55 to + 150 electrical characteristics (a t t a =25 c unless otherwise noted) characteristics symbol fr10-005 fr10-01 FR10-02 fr10-04 fr10-06 fr10-08 fr10-10 units maximum forward voltage at i o dc v f 1.3 v maximum reverse current at 25 i r 5 a maximum reverse current at100 i r 50 a maximum reverse recovery time (note 3) t rr 150 250 500 ns note: 1. measured at 1 mhz and applied reverse voltage 0f 4.0 volts 2. both leads attached to heat sink 20x20x1t(mm) copper plate at lead length 5mm 3. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a .205(5.2) .166(4.2) 1.0(25.4) min .034(0.9) .028(0.7) 1.0(25.4) min .107(2.7) .080(2.0)
fr10-005 thru fr10-10 page: 2 ratings and characteristic curve fr10-005 thru fr10-10 0 20 40 60 80 100 120 140 fig. 4-typical reverse characteristics 100 10 1 0.1 .01 instantaneous reverse current, micro amperes(ua) percent of rated peak reverse voltage t j =100 o c t j =25 o c fig. 1-test circuit diagram and reverse recovery time characteristic +0.5a 0 -0.25a -1.0a trr 1cm set time base for 10/20 ns/cm pulse generator ( note 2 ) (+) 25 v dc (approx) (-) d.u.t. 1 non inductive oscilloscope ( note 1 ) 50 no inductive 10 no inductive (-) (+) note: 1. rise time=7ns max. input impedance=1 mohms 22pf 2. rise time =10ns max. source impedance=50 ohms 1.0 cycle fig. 5-maximum forward surge number of cycles 30 20 10 0 peak forward surge current amperes 1 10 100 number of cycles at 60 hz t a =75 o c 8.3ms single half sine-wave jedec method fig. 3-typical junction capacitance f = 1 mhz vsig = 50 mvp-p tj=25 o c capacitance, pf 20 10 1 1 10 100 reverse voltage, volts 20 10 3 1 .3 .1 .03 .01 instantaneous forward current , i f ( a ) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 instantaneous forward voltage, (v) fig. 6-typical instantaneous forward characteristics tj=25 o c pulse width =300us 1% duty cycle t a -ambient temperature ( o c) fig. 2-maximum current derating curve 0 20 40 60 80 100 120 140 160 180 200 io-average rectified current ( a ) 1.0 0.8 0.6 0.4 0.2 0 i(pk) i(av) = resistive or inductive load 0.375?(9.5mm) lead length capacitive load i(pk) i( av ) 5 = 10 20
|
